Home > Drive Not > Dvd Rom Drive Not Working Windows Vista

Dvd Rom Drive Not Working Windows Vista

Contents

Reports: · Posted 4 years ago Top Lighthouse Posts: 13598 This post has been reported. If the message "device is not ready" is shown or the screen fails to update after 30 seconds, the disc or the drive may be bad. Verify that the optical disk drive is listed. Can you try the drive in another machine ? have a peek at this web-site

Step 4: Reading a disc from a command prompt Confirm that the drive can read discs from a command prompt. Select the Operating System installed on your computer to find more information about how to restore your computer to factory defaults: Windows 10 Windows 8.1 or Windows 8 Windows 7 (Dell Click the plus sign next to IDE ATA/ATAPI controllers to see if there are any problems and troubleshoot them according to the error codes in Device Manager. If the drive is not listed, refer to the Dell knowledgebase article Optical Disk Drive is not recognized in Microsoft Windows.

Windows Vista Dvd Driver Download

Back to Top Perform a Windows System Restore System Restore is a built-in Windows tool designed to protect and repair the operating system. Click the plus sign (+) next to DVD/CD-ROM Drives (or similar) category. Figure : Replacing the side panel Turn on the computer. Windows should ask for the drivers.

Make sure Master or Slave jumper setting matches the correct Master or Slave cable connector or is set to Cable Select. The other is turn the laptop over and remove the retaining screw > remove the drive > restart windows > check and make sure the drive is not showing in device Step 3: Check the drive cables Perform the steps in this section to check the drive cabling: warning: The edges of metal panels can cut skin. Dvd Drive Not Detected In Windows 10 If the DVD drive can read CDs but not DVDs, insert a DVD movie.

Watch QueueQueueWatch QueueQueue Remove allDisconnect Loading... You may need to uninstall your disc recording software, restart the computer, reinstall the CD/DVD writing software, and then restart the computer again if the software no longer recognizes the drive When done, use the CD or DVD drive again to see if it can read discs. https://support.microsoft.com/en-us/kb/939052 If the above troubleshooting steps have not been able to resolve the issue with the optical disk drive, you could try to restore your computer factory defaults as a last resort.

note: If the CD/DVD writing software that you use was purchased separately, uninstall the software, restart, and then use its installation discs to install the software, and then restart again. Dvd Drive Not Working Windows 10 In the select drive dropdown box it states drive not found. I cannot load new software, play CDs or DVDs, and I am no longer able to burn music. Sign in to make your opinion count.

  • Before beginning the diagnostic, ensure you have the proper media that you wish to troubleshoot.
  • Not something most can do without burning something up.
  • Watch Queue Queue __count__/__total__ Psst...!
  • It is probably related to the software configuration in Windows.

Windows Vista Dvd Drive Not Found Solution

Select New and Multi-String Value. http://support.hp.com/us-en/document/c00817052 If DVD/CD-ROM Drives is not in the list, skip to Step 2 to reset power or reseat the drive cables if necessary. Windows Vista Dvd Driver Download Kitts och Nevis St. Cd Drive Not Detected Windows 7 YesNo Feedback E-mail Share Print Search Recently added pages View all recent updates Useful links About Computer Hope Site Map Forum Contact Us How to Help Top 10 pages Follow us

The instructions below can be used for both internal and external CD, DVD or Blu-ray drives but some of the fundamentals might be a little different. Check This Out If you get any prompts from User Account Control while accessing Device Manager, click Yes to continue. HP Customer Support Z7_3054ICK0KGTE30AQO5O3KA30U7 hp-contact-secondary-navigation-portlet Actions ${title} Loading... A copy of the registry has saved for back-up purposes to the Documents folder. Windows Vista Cd Drive Not Reading Discs

Press Enter and type the following at the new command prompt: dir Do one of the following tasks depending on what is shown on the screen: If a list of filenames Did you scan for hardware if windows didn't find it on a restart? Scroll down and select Roxio Creator from the list. Source pspslimhacks 210,454 views 2:40 DVD Drive Not Recognized or Reading CD/DVD - Duration: 5:24.

Right-click the drive name and select Enable. Dvd Driver For Windows 7 beyourownit 243,858 views 5:03 CD Drive not detected - DVD Drive not detected - Windows 7 free fix - Duration: 2:48. In the Run dialog box, type control then press the Enter key.

No thanks Try it free Find out whyClose CD/DVD Drive not working on vista!

If there are updates available for the CD/DVD drive or recording software, select the ones that apply. note: If the drive cannot be enabled, a required software service or driver is disabled or not functioning properly. Figure : Jumper Figure : Upper IDE cable connectors Slave connector (middle) Master connector (end) Replace the cover and plug in the power, keyboard, mouse, and video cables. Cd Drive Not Working Windows 10 Figure : Example of message in Roxio Creator Basic 9 Step 5a: Reinstall disc recording software Upgrading the operating system or installing certain types of software can cause other recording software

Reports: · Posted 4 years ago Top Lighthouse Posts: 13598 This post has been reported. The following procedure is an example of how to correct a No drive detected message in Roxio Creator Basic v9. Bad data, scratches, or smudges on discs is preventing the drive from reading the data. http://intrascol.org/drive-not/dvd-drive-not-working-in-windows-vista.html About Press Copyright Creators Advertise Developers +YouTube Terms Privacy Policy & Safety Send feedback Try something new!

This can help determine if the drive has a problem reading certain types of disc formats. Try booting a CD or bootable diskette Windows 2000, XP, Vista, 7, and later users If the above recommendations do not work, boot from the Windows disc to see if the Intel Pentium Dual Core Processor with super multi DVD burner/labelflash with plenty of memory on both C and D hard drives.Here are the things I have done so far. When Windows opens, wait until the Found new hardware wizard fully configures the drive.

NazmusLabs 386,193 views 16:05 Loading more suggestions... Loading... Reports: · Posted 4 years ago Top garyallen349 Posts: 111 This post has been reported. When I removed the drive the last time and then reinstalled it when I booted up I got a message stating that windows was unable to install a device.

Figure : Command Prompt window Type Exit and press the Enter key to return to the command prompt. Microsoft Windows Windows 10, Windows 8.1 and Windows 8 Microsoft Windows Windows 7, Windows Vista and Windows XP Back to Top Install the latest BIOS update on your computer Dell recommends Shailesh Sharma 459,774 views 7:52 CD/DVD Drive Not Showing/Missing In My Computer - Duration: 6:38. I have removed the drive and then restarted to make sure device is not mentioned in device manager.

Close Device Manager and skip to Step 2 to reset power and reseat the drive cables if necessary. For more information about testing for CD/DVD drive hardware failures, refer to the HP support document Using HP Hardware Diagnostics Tools to Test for Hardware Failures. Click the Restore Defaults button. Figure : Device Uninstall button The drive name should be removed from the list (and the DVD/CD-ROM drives category will also be removed if there is only one CD/DVD drive).

Please help. Not really, you would need the proper equipment plus know the pinout reading. For more information about using System Restore, use the the HP support document Using Microsoft System Restore in Windows Vista.