You just saved me $70.00! Patrick Was this answer helpful? Yes No Voted Undo Score 5 Cancel Comments: The DC14 has a clutch that engages or dis-engages the beater bar depending on floor type. Lay machine down so hose on floor and dust collector on top. Source
Can't get the clutch assembly off yet to replace it. Yes No Voted Undo Score 0 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? Turn the end and locate it properly. I have the DC 15 ball all floors.
They are a hand-held. There are two switches right next to each other, one is for the suction, the other for the roller brush, make sure both switches are turned to the on position. Mending a pair of M-AUDIO BX5a monitors One of my sons friends asked me if I could take a look at his speakers which had stopped working. the brush bar turns if i hold it on.
Suzanne on September 19th, 2014 at 1:34 pm Manfromcleves on Jan 5th 2013 you are a star. Sure enough, the culprit was a small, dense hairball lodged under the belt inside the clutch mechanism. Mayor: An expert whose answer got voted for 2 times. Dyson Dc39 Brush Not Spinning DC25 brush bar not working - Dyson Spare Parts with Free ...
I was able to read your post and comments and fix mine the exact same way. Dyson Dc24 Brush Not Spinning If I lift it off the floor it spins, once it touches the floor it stops. Gerry G on May 20th, 2014 at 1:00 pm Hi, it seems after some investigation my dc04 needs a belt changing, I think that can be easily achieved but there doesnt Thanks That sounds like a clutch or seized brushroll bearings - possibly both.
If this doesnt resolve the issue, please contact our Helpline on 0800 298 0298 (UK) or 1866MYDYSON (US). Dyson Dc50 Brush Bar Not Spinning Actual savings may vary based on use and other factors. ***Calculated lifetime based on LED L70.****Based on Tolomeo lettura halo aluminium reading lamp using a 70W halogen bulb at a cost Rating is available when the video has been rented. Wow this saved me from thinking I needed to have my vac serviced.
This is here to help protect the belt from burning if something gets stuck in the vacuum while it's on. https://www.dyson.com/support/dc24new/dc24-animal/my-machine-is-not-working/brushbar-not-rotating-reset-check Mayor: An expert whose answer got voted for 2 times. Dyson Dc25 Brush Not Spinning I was getting ready to order a new clutch assembly and beater bar. Dyson Animal Brush Not Spinning I have had my Dyson in bits trying to work out why the roller wasn't working.
Copy Protected by Chetan's WP-Copyprotect. this contact form Actual savings may vary based on use and other factors. ***Calculated lifetime based on LED L70.****Based on Tolomeo lettura halo aluminium reading lamp using a 70W halogen bulb at a cost If your machine doesn't have a clutch, and the brush bar is not spinning, check the drive belt, it has probably snapped and wants replacing. It might be the brush bar motor or the power switch to the brush bar motor. Dyson Animal Brush Bar Not Spinning
I thought it may be an electrical connection problem but have tried to change the pressure at the connection points but this has no effect. However both belts seemed extremely shiny on the side which engaged with the clutch. If I pull the soleplate front down again, it works fine until it pops back up. have a peek here GoVacuum Mar 20, 2010 | Dyson DC15 All Floors - The Ball Bagless... 1 Answer On my dyson DC24 the beater bar attachment is not working.
Any ideas? Dyson Dc40 Brush Bar Not Spinning manchestervacs.co.uk/DysonForum/index.php?topic=738.0 DC25 brush bar not working ... Working...
I soldered in a 3" wire to extend the length of the broken wire. First I needed to remove the lower plate. Posted on Nov 23, 2009 Helpful 4 Not Helpful Comment Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images Hawk Wala Level 1: An expert Dyson Dc41 Brush Bar Not Spinning Dry times calculated using Dyson test method 769 based on NSF protocol P335 using a measurement of 0.1g residual moisture.7Dry time measured using Dyson test method 769 based on NSF P335
Just fixed mine using your instructions. Posted on Feb 28, 2011 Helpful 1 Not Helpful Comment Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images desthompson Level 1: An expert who Peter on November 30th, 2014 at 11:19 am Hi, I have a DC04 where the roller is not rotating. Check This Out Shannon Surerus on April 25th, 2012 at 10:41 pm Dyson DC14, brush will not turn when vacuum is on, in reclined position, it does have a clutch.
Now my brush is spinning again. There is a switch by the main power switch that provides power to run the brush bar motor. I picked the ruber seal out and used ice pick to expand hole; made it easy to get wire through. Autoplay When autoplay is enabled, a suggested video will automatically play next.
Chuck Fresh 301,683 views 7:45 Review: Dyson DC39 (Multi-Floor Vacuum Cleaner) - Duration: 6:54. I heard that noise before when i would get a string or such wrapped around the roller. Just luck out sometimes and then sometimes I don't. Angus Black on May 15th, 2012 at 4:04 pm oh and I should have said its a dc07, there was a smell of burning but i assumed that was the belt