Home > Water Heater > Electric Hot Water Heater Bottom Element Not Working

Electric Hot Water Heater Bottom Element Not Working

Contents

we popped the panel and there is water in there.there is a silver hexagon thing it looks like that is where the water is coming from what do we do? You may get the same reading if there is an internal open in the element. What causes this? How can I make it go up so I can push it down to reset it? http://intrascol.org/water-heater/electric-rv-water-heater-not-working.html

what was causing it to smoke??? Flag as duplicate Thanks! Browse other questions tagged electrical water-heater or ask your own question. Below we show how to find the thermostat control and reset switch for an electric water heater.

How To Test Hot Water Heater Thermostat

Simply use a socket and ratchet or other suitable wrench to remove the 4 bolts and remove the element. Hardly any water came out of the drain. On a 17 year old water heater I would recommend replacement as the most viable option. The dial may indicate letters "A" "B" "C" etc., "warm, hot and hotter" or as in the case of the one pictured, the actual temperature in degrees.

  1. Make sure the tester is working by putting the tip into an outlet you know has power.
  2. setting higher it solved the problem, except once before that the temp.
  3. Mark Henley, Journeyman Technician Category: HVAC Satisfied Customers: 3217 Experience:UA Journeyman Pipefitter , HVAC, Refrigeration, DDC controls. 26 years.Commercial & residential Mark Henley and other HVAC Specialists are ready to help
  4. Most analog meters that do not provide manual range selection likely support only a single range.

When testing the thermostats be aware that you must test the input and output sides. Reader Question: should the upper and lower temperature thermostats be set the same on a water heater? How can I safely handle a concentrated (fuming) nitric acid spill? My Water Heater Is Not Heating Water The thermostat testing procedure is complex, so we recommend simply replacing the thermostat(s).

If your old element isn’t labeled with the wattage, refer to the nameplate on the water heater or your instruction manual, or search online using the model number from the nameplate. can you help? Derek7 years ago Just out of curiousity, I have replaced my lower element 5 times over the past 3 years. Any idea what could be going on?

Blaquewraithe4 years ago L Burke,1st off checking to ground is not a diagnostic technique you can trust for anything but safety! How To Tell If Electric Water Heater Is Working Sears PartsDirect 160,620 views 8:35 Replace Water Heater Element with Full Tank of Water - Duration: 9:32. Can you provide an answer? How Duel Element Electric Water Heaters Work Cold water enters the bottom of the tank through a fill tube inside the tank.

Electric Water Heater Thermostat Troubleshooting

If the temperature of the water in the bottom part of the tank is higher than the lower thermostat's setting, the lower thermostat remains "off" and voltage is prevented from reaching HiCustomer/p>There was some trouble in getting back to you. How To Test Hot Water Heater Thermostat This worked for about 1 day then water got over hot again, 150 deg, and hwh shut off. How To Test Water Heater Element It's a 40-gallon tank.

Try pushing the button on the “high-temperature cutoff,” located just above the upper thermostat. http://intrascol.org/water-heater/electric-water-heater-not-working.html Expert: plumber 171 replied7 years ago. Read the rest of this step slowly and carefully (and repeatedly if needed) until it makes sense as it is the "why and how" the thermostats work together. When one guy got tired of humming another prisoner picked it up. Hot Water Heater Reset Button

Heating Element: Has two terminals with a wire connected to each. Your post gave me the clue to figure it out. The only problem I can think of is we burnt up both elements. navigate here This is a detailed, comprehensive article with additional help on the discussion page.

Only the upper thermostat has a reset button. Water Heater Thermostat Problems How long did you leave it sit after changing the elements ?ThanksMark. It is a 5000 watt element, and I can’t pull it out.

By code the only hose ever to be used on a water heater is to drain it.

A propane flame should have a bluish green flame with a tinge of yellow at the tip. You may need to drain water pressure from the system or even drain piping in order to make repairs, especially if soldering is needed. This series of articles describes how to inspect, operate, diagnose, and repair electric hot water heaters. Water Heater Tester edgar4 years ago is water suppose to be coming out of the thearmostat Deb4 years ago It has been 3 years since a response from handymanpro.

Checked the incoming voltage to the two hot wires. improper wiring connection during the repairs 3. Press the black probe firmly against the metal tank or the heating element mounting nuts or screws (not the other terminal screw). his comment is here No screws are used.

Be sure to be sure the value displayed is really simply as reading the number displayed, and not the 1000 (kilo or K multiplier) or the 1,000,000 (meg M multiplier). Carson Dunlop Associates' provides extensive home inspection education and report writing material.The Illustrated Home illustrates construction details and building components, a reference for owners & inspectors. If desired, the range may be lowered to any desired - provided the range is greater than the voltage displayed at the highest range. Now we have a water heater that's full, wired, and definitely receiving power to both elements, but it just won't heat the water.

Hot Network Questions Music notation software for ubuntu How do I deal with my current employer not respecting my decision to leave? is scalding and a mixing valve may be needed for safety. See Electric Water Heater Reset Switch in the article above. the thermostat is bad.